HJ2541 Dual-Channel Power Operational Amplifier
Release time:
2020-10-30
Hangjing Microelectronics has launched a series of domestically produced alternative integrated circuit products. Below is an introduction to Hangjing Microelectronics HJ2541, which completely replaces OPA2541.
Hangjing Microelectronics has launched a series of domestically produced alternative integrated circuit products. Below is an introduction to Hangjing Microelectronics HJ2541, which completely replaces OPA2541.
HJ2541 compared to OPA2541
1) Both are in a TO3-8 package, using low thermal resistance fixed BeO (beryllium oxide) high thermal conductivity thick film substrates to achieve dual-channel power amplification.
2) The output current capabilities of both are comparable. However, the operating voltage of HJ2541 can only reach ±18V.
3) The power NPN and PNP transistors of OPA2541 are both front-leaded, resulting in high Rc, high thermal resistance, and heat concentration due to chip area constraints. In contrast, HJ2541 separates amplification and power drive within the thick film circuit and uses vertical power NPN and PNP transistors, resulting in lower and more dispersed heat generation. This approach improves the reliability of the device.
4) All materials used are domestically sourced.
5) In a ±15V analog distribution system, both can be completely interchangeable without any modifications.
HJ2541Dual-channel power operational amplifier
HJ2541 is a dual-channel power operational amplifier capable of providing up to 5A output current. It integrates two power amplifiers into a single package, offering unparalleled power density that can directly replace OPA2541 in medium voltage applications.
The use of a TO3-8 metal shell package completely isolates it from internal circuits, eliminating the need for insulators that would reduce thermal performance; it can be directly mounted on a heatsink. The internal circuit limits the output current to approximately 6A. It can be applied in fields such as motor drivers, servo amplifiers, voice coil drivers, bridge amplifiers, programmable voltage sources, audio amplifiers, etc.
2. Electrical principle block diagram
3. Package form and pin function
1) Uses TO3-8 metal round shell fully sealed packaging.
2) Pin definitions
4. Absolute maximum ratings
5. Electrical characteristics
(Unless otherwise specified T = 25 °C, VS = ±15V)
6. Typical applications
Key words:
OPA2541, dual power operational amplifier, power op-amp
Previous Page
Next Page
Previous Page:
Next page:
recommend News
A Deep Dive into Rail-to-Rail Amplifier Specifications and Performance Metrics
A Deep Dive into Rail-to-Rail Amplifier Specifications and Performance Metrics Table of Contents 1. Introduction to Rail-to-Rail Amplifiers 2. How Rail-to-Rail Amplifiers Work 3. Key Specifications of Rail-to-Rail Amplifiers 4. Important Performance Metrics 5. Real-World Applications of Rail-to-Rail Amplifiers 6. Comparing Rail-to-Rail Amplifiers with Standard Amplifiers 7. Design C
2026-08-31
Maximizing Sensor Performance with Rail-to-Rail Amplifiers
Rail-to-rail amplifiers are essential components in sensor interfaces, especially in electronic devices that require high precision and accurate signal processing. These amplifiers are designed to maximize the output voltage swing, allowing them to operate effectively across the entire supply voltage range. This characteristic is particularly advantageous for applications where signal levels can a
2026-08-28
How to Select the Right Low Voltage Rail-to-Rail Operational Amplifier for Your Needs
How to Select the Right Low Voltage Rail-to-Rail Operational Amplifier for Your Needs Table of Contents Understanding Rail-to-Rail Operational Amplifiers Importance of Low Voltage Amplification Key Specifications to Consider Gain-Bandwidth Product Input and Output Voltage Range Power Supply Requirements Slew Rate and Settling Ti
2026-08-25
Enhancing Data Acquisition: The Role of Precision Amplifiers in Electronic Systems
Precision amplifiers are critical components in data acquisition systems, primarily because they enhance the accuracy and reliability of signal processing. These amplifiers are designed to amplify low-level signals while minimizing noise, thereby ensuring that the data collected is both precise and representative of the actual conditions being measured. In environments where signal integrity is pa
2026-08-22
A Comprehensive Guide to Calibration Techniques for Instrumentation Amplifiers in Bridge Sensors
A Comprehensive Guide to Calibration Techniques for Instrumentation Amplifiers in Bridge Sensors Calibration is a crucial process in the operation of instrumentation amplifiers, particularly when they are employed in bridge sensor applications. Accurate calibration ensures that your sensors provide reliable data, which is essential for precise measurements in various applications, including indust
2026-08-19