MXT7660 Charge-Pump Inverter

Revamping Your Electronic Projects with Operational Amplifiers for Analog Signals Table of Contents Understanding Operational Amplifiers: The Basics The Importance of Operational Amplifiers in Electronic Projects How Operational Amplifiers Function Applications of Operational Amplifiers in Analog Signal Processing Designing Circuits with Operational Amplifiers for
  I. Overview
  The MXT7660 charge‑pump inverter is fabricated using a mature high‑voltage AL‑gate CMOS process. This device requires only two external capacitors to convert an input voltage of +2.5 V to +10 V into an output voltage ranging from −2.5 V to −10 V. It eliminates the need for inductors, thereby reducing losses and electromagnetic interference. The circuit comprises a voltage regulator, an RC oscillator, a level‑shifting stage, and MOS power transistors. With a supply voltage of 5 V and pin 7 left open, the internal local‑oscillator frequency is 10 kHz. The MXT7660 is suitable for LCD display driving, supplying negative power rails for RS‑232 interfaces, data acquisition, and providing negative supplies for instrumentation amplifiers. Its key features are as follows:
  +5V converted to ±5V; wide supply voltage range: 2.5V to 10V
  High voltage conversion efficiency: 99.9% (typical value) High power supply conversion efficiency: 98% (typical value)
  Low power consumption: Is ≤ 40 µA (at +5 V supply); few external components, easy to use.
  High electrostatic breakdown voltage: ≥3 kV; when operating at high voltages, a Dx diode is not required.
  The black ceramic SO-8 package is better suited to the stringent requirements of military-grade products for high reliability and high assembly density.
  II. Electrical Schematic Diagram
  3. Package Type and Lead Terminal Functions
  1. Package Type
  It employs a TO-08 metal hermetic package, a D08S2 ceramic dual‑in‑line package, and an SO-08 black ceramic micro‑package.
  (TO-08 • Top View) (D08S2 • Top View) (SO-08 • Top View)
  2. Lead-out Terminal Functionality
  Pin numbers 1, 2, 3, 4, 5, 6, 7, 8
  Symbol NC C+ GND C- OUT LV OSC V+
  Function: external capacitor positive terminal, external capacitor negative terminal, low-voltage output, oscillation capacitor selection, input voltage.
  IV. Absolute Maximum Ratings
  The power supply voltage is +10.5 V, and the output short-circuit duration is unlimited (V+ ≤ 5.5 V).
  Storage temperature: −65°C to +150°C; Operating temperature range: −55°C to +125°C.
  Power consumption: 500 mW (SO-8); LV and OSC input voltage range: −0.3 V to V++0.3 V (V+ ≤ 5.5 V)
  730 mW (TO-8/D08S2) V±5.5 V to V++0.3 V (V+ > 5.5 V)
  5. Electrical Characteristics
  Unless otherwise specified: V+=+5V, OSC=NC, TA=+25℃
  Parameter Name Symbol Test Condition Nominal Value Unit
  Minimum Typical Value Maximum
  Quiescent current IS RL=∞ 40 1 µA
  Input high voltage V+H LV=NC 3.5 10 V
  Input low voltage V+L LV=0V 2.5 3.5 V
  Output resistance Rout, Iout = 20 mA, 70 Ω
  Iout=5mA,V+=3V 120
  Oscillation frequency FOSC 10 kHz
  Power efficiency PEFF RL=5kΩ 95–98%
  Conversion accuracy VOEFF RL=∞ 98 99.9%
  VI. Typical Applications
  1. Application of positive voltage to negative voltage 2. Generation of –10 V from +5 V
  Note: When V+ ≥ 3.5 V, K is open; when V+ < 3.5 V, K is closed. Note: In this case, the output impedance equals the sum of the impedances of the two devices.
  VII. Required Explanations
  1. The input voltage must not exceed the maximum rated value.
  2. When the input voltage exceeds 3.5 V, the LV terminal must not be grounded.
  3. When the input voltage exceeds 5.5 V, the output terminal must not be shorted to ground for an extended period.
  4. Strictly observe the polarity markings on the capacitor as indicated in the schematic; do not reverse the connections.
  5. If the source impedance of the power supply for this device is relatively high (25 Ω–30 Ω), a 2.2 µF capacitor should be connected between pin 8 and ground.
  6. When the output voltage is ≥0 V, device latch-up may occur, leading to device failure. To prevent this, a 1N914 diode can be connected between the output and ground, with its anode connected to pin 5 and its cathode connected to pin 3.
  7. At TA = +125°C, derating of the device’s output current is required.

Keywords:

Hot News

Leave a Message Online

Submit Message

*Note: Please ensure that all information provided is accurate and keep your contact details up to date. We will get in touch with you as soon as possible.

Company Message

Submit Message

*Note: Please ensure that all information provided is accurate and keep your contact details up to date. We will get in touch with you as soon as possible.

Request for Samples / Product Manuals / Contact Information:


Mr. Jia:13022932841(WeChat)

 

                18009180846  

 

Landline:029-89259995Transfer 833

 

 

Technical Support / Contact Information:


Mr. Zhao:13572473285
Landline:029-89259995Transfer to 803


Ms. Xu:18729396827
Company landline:029-89259995

Fax: 029-89259996

Unit 4, Building 6, Beihang Science and Technology Park, Hangtian Middle Road, Aerospace Base, Chang’an District, Xi’an, Shaanxi Province

Official Account

%E7%AC%AC%E4%B8%80%EF%BC%8C%E6%9C%80%EF%BC%8C%E4%BC%98%E7%A7%80%EF%BC%8C%E5%A2%9E%E5%BC%BA%EF%BC%8C%E4%B8%80%E6%B5%81%EF%BC%8C%E5%8D%93%E8%B6%8A%EF%BC%8C%E9%A2%86%E5%85%88%EF%BC%8C%E5%85%88%E8%BF%9B%EF%BC%8C%E5%BC%95%E9%A2%86

Sorry,当前栏目暂无内容!

您可以查看其他栏目或返回 首页

Sorry,The current column has no content!

You can view other columns or return Home