Application

28

2021-07

2021-07-28

Analog and switching characteristics of electronic analog switches

Many engineers, when using analog switches for the first time, often treat them as if they were mechanical switches. In fact, although analog switches do function as switches, they differ from mechanical switches and also exhibit semiconductor characteristics: Analog Switch Characteristics (1) On‑resistance (Ron) varies with the input signal (Vin) Figure 1a shows a simplified schematic of an analog switch. As illustrated, the normally open and normally closed paths are actually formed by two complementary pairs of N‑channel and P‑channel MOSFETs, enabling bidirectional signal transmission. If we parallel the on‑resistances of the P‑channel and N‑channel MOSFETs corresponding to different Vin values, we obtain the relationship shown in Figure 1b, depicting how Ron changes with input voltage (Vin). Neglecting temperature and supply‑voltage effects, Ron varies linearly with Vin, which can lead to variations in insertion loss and introduce total harmonic distortion (THD) in the analog switch. Additionally, Ron is also influenced by the supply voltage; typically, it decreases as the supply voltage increases. (2) Analog switches have strict input signal limits Since analog switches are semiconductor devices, when the input signal falls below the negative supply voltage or exceeds the positive supply voltage, the MOSFETs enter reverse bias. Once the voltage surpasses a certain threshold—typically 0.5 to 4 V—the switch ceases to operate properly, and in severe cases may even be damaged. Therefore, during application, it is crucial to ensure that the input signal remains within the specified range. The circuitry of an analog switch can be equivalently represented as shown in Figure 2. (3) Charge injection When designing mechanical switches, we naturally prefer lower Ron values, as reduced resistance minimizes signal loss. However, for analog switches, low Ron is not always advantageous: achieving lower Ron often requires a larger chip area, resulting in increased input capacitance (parasitic capacitance). The charge variation caused by the parasitic capacitances associated with the NMOS and PMOS transistors in the analog switch is known as “charge injection.” During each switching cycle, the charging and discharging processes consume additional current and generate both positive and negative spikes. With a time constant t = RC, the charging time depends on the load resistance R and capacitance C, typically lasting several tens of nanoseconds. This indicates that lower Ron leads to longer turn‑on and turn‑off times. Consequently, selecting an analog switch requires carefully balancing Ron against charge injection. (4) Induced signals leak even when the switch is off This characteristic refers to the phenomenon where, when transmitting AC signals, some portion of the signal still leaks through induction from the input to the output, or between channels, even when the switch is open. Generally, the higher the signal frequency, the more pronounced this leakage becomes. (5) Relatively small transmission current Unlike mechanical switches, analog switches typically handle only small currents. Currents allowed under continuous operation in modern CMOS‑based analog switches usually remain below 500 mA. (6) Extremely low drive current at the logic control terminal In contrast to mechanical switches, whose logic control terminals often require milliampere‑level drive currents—sometimes making direct digital I/O insufficient—analogue switches demand only minuscule drive currents, typically less than nanoamperes. Thus, they can be driven directly by digital I/O, helping to reduce power consumption and simplify circuit design. Switching Characteristics of Analog Switches (1) Bidirectional signal transmission Some people habitually designate the two normally open/normally closed terminals of an analog switch as the input terminals and the common terminal as the output terminal. However, this is merely a temporary convention based on specific application requirements. Most analog switches support bidirectional signal transmission; ignoring this feature can easily lead to circuit problems such as reverse biasing voltages or backflow of current. (2) Extremely low leakage current when switched off When an analog switch is turned OFF, it presents a high‑impedance state, with leakage currents between the two transmission terminals being extremely small—typically below the nanoampere level. Many analog switches exhibit leakage currents around 1 nA after being switched off. Such negligible currents can generally be ignored in practical applications, effectively treating the switch as ideally off. The equivalent circuit of an analog switch in the OFF state is shown in Figure 3. In summary, analog switches are semiconductor devices with switching functionality. When applying them, it is essential to fully exploit their switching capabilities while accounting for their semiconductor characteristics; otherwise, unexpected issues may arise.

< 12 >

Company Message

Submit Message

*Note: Please ensure that all information provided is accurate and keep your contact details up to date. We will get in touch with you as soon as possible.

Request for Samples / Product Manuals / Contact Information:


Mr. Jia:13022932841(WeChat)

 

                18009180846  

 

Landline:029-89259995Transfer 833

 

 

Technical Support / Contact Information:


Mr. Zhao:13572473285
Landline:029-89259995Transfer to 803


Ms. Xu:18729396827
Company landline:029-89259995

Fax: 029-89259996

Unit 4, Building 6, Beihang Science and Technology Park, Hangtian Middle Road, Aerospace Base, Chang’an District, Xi’an, Shaanxi Province

Official Account

%E7%AC%AC%E4%B8%80%EF%BC%8C%E6%9C%80%EF%BC%8C%E4%BC%98%E7%A7%80%EF%BC%8C%E5%A2%9E%E5%BC%BA%EF%BC%8C%E4%B8%80%E6%B5%81%EF%BC%8C%E5%8D%93%E8%B6%8A%EF%BC%8C%E9%A2%86%E5%85%88%EF%BC%8C%E5%85%88%E8%BF%9B%EF%BC%8C%E5%BC%95%E9%A2%86

Sorry,当前栏目暂无内容!

您可以查看其他栏目或返回 首页

Sorry,The current column has no content!

You can view other columns or return Home