Introduction to the Three-Wire 4–20 mA Silicon Piezoresistive Bridge Transmitter
Release Date:
2019-11-21
Source:
Author:
Silicon piezoresistive Wheatstone‑bridge sensors are currently the most widely used pressure sensors in industry. Their advantages include low cost and suitability for mass production. Their drawbacks, however, are zero‑offset and full‑scale nonlinearity. (FSO) It has large errors, poor linearity, and significant temperature drift.
MAX1452 A lookup-table‑based temperature compensation is provided, enabling the silicon piezoresistive Wheatstone bridge to operate reliably over a wide temperature range and effectively enhancing measurement accuracy. Its output is an analog voltage, which is not well suited for long‑distance transmission.
However, in practical applications, transmitters built with the MAX1452 must be spaced at a certain distance from subsequent data acquisition systems, and electrical connectors may need to be interposed between them. The parasitic electrical parameters of the cables are significant, resulting in a poor signal-to-noise ratio at the cable’s far end under complex electromagnetic conditions, which severely compromises measurement accuracy.
Since the current in the loop is not affected by the parasitic inductance (L) and parasitic capacitance on the cable ( C ) and the series resistor ( R ) Consequently, the prevailing engineering consensus is that loop currents can be transmitted over relatively long distances without compromising the signal-to-noise ratio. Industrial standards 4 ~ 20mA The concept of the current loop is formulated based on the aforementioned facts and is widely applied.
Shaanxi Hangjing Microelectronics’ HJ14521 is a precision three-wire device integrated using thick-film technology. 4 ~20mA The current-output silicon piezoresistive sensor conditioning circuit primarily comprises the MAX1452 analog sensor signal‑processing circuit, a linear regulated power supply, a precision reference voltage source, multiple precision wideband operational amplifiers, and several precision matched resistor pairs. The entire device is powered by a single supply, with the floating GNDI serving as the reference ground for the MAX1452, thereby converting the MAX1452’s output voltage… 0 ~5V Convert to output current 4 ~20mA Output, with further optimization in use, can support long transmission lines, enhancing noise immunity and increasing integration. It is capable of withstanding extreme environmental stresses and harsh electromagnetic conditions.
Conventional silicon piezoresistive transmitters typically provide voltage outputs; this particular silicon piezoresistive transmitter can convert pressure signals into a proportional output. 4~20mA It is a current‑signal device with a compact structure and comprehensive protection features. A protective diode is incorporated at the output to safeguard against surge voltages on the output leads, while the power input includes reverse‑polarity protection. With excellent performance, it addresses the shortcomings of the MAX1452; certain circuit sections have been redesigned. Although the MAX1452 datasheet specifies that the device’s internal dedicated operational amplifier can be used, a two‑wire configuration can also be implemented by integrating discrete external components in part of the circuit. 4 ~20mA Current-output loop. However, due to poor performance specifications of the internal discrete operational amplifiers, an inadequate architecture for voltage-to-current conversion, limited temperature tolerance, and difficulties in system integration, this approach is rarely employed in practical engineering applications.
Three-wire system controlled by HJ14521 4 ~20mA The electrical schematic of the transmitter is as follows:
![]() |
Note “
“It is floating and cannot be connected to the supply ground.” PGND Connected.
To prevent incorrect wiring and ensure ease of use, the transmitter is equipped with three separate interfaces: the piezoresistive bridge is connected to port P1, the power supply and current output are connected to port P2, and the calibrator is connected to port P3; do not exceed these designated connections.
Instructions for Use
1. Input power supply voltage: 10V ~ 40V, Namely, the Vcc and PGND of P2 are determined by the impedance of the output leads. For aerospace products, a wide supply range of 28 V is typically used ( 16V ~ 36V) . It is recommended to use 4 ~20mA The current-loop receiver converts the signal into a voltage at the terminal.
2. Output Current Setting:
(a) P4 open-circuit output 4 ~20mA Current:
I OUT (mA) = 0.51·(V 01 + 1.23) /R SET )
(b) P4 shorted, output 0 ~20mA Current:
I OUT (mA) = 0.51 · V 01 /R SET
V 01 It is the output voltage of HJ1452.
If the terminal is connected to a 250-ohm resistor (typically a precision resistor), the output… 4 ~20mA When current flows, the output voltage is 1 ~5V ; output 0 ~20mA When current flows, the output voltage is 0 ~5V。
The general configuration of the terminal receiver is shown in the figure:
![]() |
3. Operating temperature range -55 ℃ ~ 160 ℃
4. External dimensions: Transmitter external dimensions 28 mm × 15 mm × 4.3 mm
1. The ground of the MAX1452 calibration system must not be connected to the power supply’s PGND. Connect the calibration system’s ground to the transmitter’s GND1.
2. The low side of the piezoresistive bridge must never be connected to the power supply’s ground (PGND); instead, it is tied to the P1 terminal. (In practice, it is internally connected to GND1 within the transmitter.)
3. The transmitter has separated DIO and V01.
4. After calibration, connecting UNLOCK to GND1 can enhance noise immunity.
5. The MAX calibration procedure needs to be performed only for the voltage output of the MAX1452; the current‑to‑voltage conversion loop does not require calibration.
6. The value of the adjustment resistor Rb for the transmitter is determined by the following equation: 2 mA ≤ (V cc - 6.25) / R b ≤ 10mA ,
7. In V cc It is best to adjust the Rb value when approaching the low voltage of 10 V or the high voltage of 40 V. . At the factory, Rb is set to 2.7 kΩ.
8. About V cc The problem of minimum and maximum values:
V cc The maximum value cannot exceed 40 V, due to the op-amp’s voltage‑rating limitations.
V cc min cannot be less than 20 mA × (R SET + R T ) + 5V; ensure sufficient headroom for the op-amp.
9. +V cc , PGND, I OUT Triple-twisted, which can improve electromagnetic compatibility.
10. The time drift of the piezoresistive bridge cannot be eliminated by this device.
11. It is recommended to use hook‑welding to connect the external lead wires. A U‑shaped groove is used for threading the wire.
12 The transmitter is typically installed using two… f The 2.5 mm mounting holes are secured to the substrate. However, due to their small size, they can also be fixed by heat-shrinking with a heat‑shrink tube.
13. If users have special requirements, customizations can be arranged upon request.
14. The sample has not undergone “three‑proof” treatment; users are advised to take precautions against icing when conducting low‑temperature experiments. / The effects of frost.
15. The transmitter printed circuit board is shown in the attached figure:
![]() |
Front of the 4–20 mA piezoresistive transmitter
![]() |
Back side of the 4–20 mA silicon piezoresistive transmitter
Shaanxi Hangjing Microelectronics Co., Ltd.
Phone: 029-89259995
Fax: 029-89259996
E-mail: hj@hangjingic.com
Website: www.hangjingic.com
Address: Floor 9, Building 3, No. 299, Industrial Road No. 2, Xi’an Aerospace Base
Keywords:
Hot News
Leave a Message Online
*Note: Please ensure that all information provided is accurate and keep your contact details up to date. We will get in touch with you as soon as possible.
Request for Samples / Product Manuals / Contact Information:
Mr. Jia:13022932841(WeChat)
Landline:029-89259995Transfer 833
Technical Support / Contact Information:
Mr. Zhao:13572473285
Landline:029-89259995Transfer to 803
Ms. Xu:18729396827
Company landline:029-89259995
Fax: 029-89259996
Unit 4, Building 6, Beihang Science and Technology Park, Hangtian Middle Road, Aerospace Base, Chang’an District, Xi’an, Shaanxi Province



